Refresh and protect an oiled floor — no colour change
Admonter Maintenance Oil Natural feeds an oiled timber floor back to life. It soaks into the wear layer, tops up the oil that traffic and cleaning strip out, and leaves the natural colour exactly as it was. One litre covers roughly 70 to 100 square metres. It’s for oiled floors only — never lacquered.
Coverage figure: Admonter product data (~70–100 m²/L).
Volume
1 litre
For
Oiled floors only
Job
Refresh & protect
Colour
Clear — no colour change
Coverage
~70–100 m² / L
Made in
Austria
Oiled floors only — never lacquered or waxed
This is a penetrating oil. It only works on a floor that’s already oiled, where it can soak into the timber. On a lacquered, varnished or waxed floor it can’t get in — it sits on top, stays tacky and streaks. If you’re not certain your floor is oiled, check before you start and test a small, out-of-the-way area first.
Feeds the timber
Tops up the oil that traffic wears away
The oil soaks into the wood and rebuilds the surface, so an oiled floor keeps its natural, matte feel instead of drying out in the walkways.
Vienna Woods · engineered oak flooring
What it’s for
Maintenance for an oiled floor, not a one-off fix
An oiled floor is finished with oil that soaks into the timber rather than sitting on top like lacquer. That’s what gives it the soft, natural feel — but it also means the oil wears down over time, first in the busy paths through a room.
This tops it back up. It replaces the oil that traffic has worn away and reinforces the surface, without changing the colour. On a natural-toned oiled floor it keeps the raw, matte look the floor was designed to have.
It suits homes and light commercial floors. For a badly worn floor a maintenance coat may not be enough — this is for keeping a sound oiled floor in good order, not rescuing one that’s past it.
Coverage
70–100m² per litre
A little covers a lot
One litre refreshes roughly 70 to 100 square metres in a maintenance coat. A dry, thirsty floor drinks more, so treat the figure as a guide.
How to use
Clean first, then oil
Clean the floor thoroughly first with an intensive cleaner and let it dry completely. The oil needs bare, clean timber to soak into — anything left on top stops it absorbing.
Open windows and keep the room well ventilated. Shake the tin and work one small section at a time.
Spread a thin, even coat with the grain, using a cloth, pad or buffing machine. Thin is the rule — too much oil won’t soak in and stays tacky.
Buff off any excess and let it cure. Keep traffic off until it’s dry (follow the tin for the exact time).
Lay any oil-soaked cloths or pads out flat to dry outdoors, or soak them in water before you bin them — see the safety note below.
Coverage is a guide (~70–100 m²/L) — a thirsty, dried-out floor drinks more.
When to reach for it
Reach for it when
An oiled floor looks dry, patchy or worn in the walkways.
It’s due for routine maintenance to keep the surface protected.
You want to refresh the oil without changing the floor’s natural colour.
Aftercare
Keeping it looking its best
Do
Clean and fully dry the floor before you oil.
Apply thin coats and buff off the excess.
Keep the room well ventilated while you work and until it’s dry.
Lay oily rags out flat outdoors to dry, or soak them in water before disposal.
Don’t
Don’t use it on a lacquered, varnished or waxed floor.
Don’t pile on thick coats — it won’t absorb.
Don’t bin oily rags straight into a rubbish bag (fire risk — see safety).
Don’t walk on it or replace rugs until it’s fully cured.
Complete the system
The rest of the Admonter care range
Clean the floor first, and the white-tinted oil for light floors.
Clean
Admonter Clean & Care
The everyday concentrate to clean an oiled floor between oilings.
Admonter Maintenance Oil is a solvent-based product. Keep the room well ventilated while you work and follow the safety directions on the tin and the manufacturer’s Safety Data Sheet. Important: cloths, pads and mops soaked with this oil can heat up and catch fire on their own as the oil dries. Lay them out flat to dry outdoors, away from anything that can burn, or soak them in water before you throw them away — never leave them screwed up in a pile or a bin.
Colour: Clear
Coverage: 1 litre should cover 70 – 100m2
Deep Nourishment: Specially formulated to penetrate the inner layers of your oak flooring, this maintenance oil revitalises the wood, ensuring a vibrant and fresh appearance.
Superior Protection: Offering a robust protective layer, it shields your flooring from everyday wear and tear, preserving its pristine condition and longevity.
Eco-Friendly Composition: Aligned with our commitment to sustainability, this oil is made from natural ingredients, ensuring safety for both your home and the environment.
Ideal for High-End Flooring: Perfectly suited for the premium engineered oak floors we provide at Vienna Woods, this oil is the top choice for architects, interior designers, and discerning homeowners across New Zealand.
